Dynalite DMC810GL Installation Manual download pdf (Page 8)

Trouble shooting

DMC810GL Installation Manual Rev E.docx 8

Check the following list. If you are still unable to rectify the situation, contact your nearest Dynalite office. A complete list of

distributors worldwide can be found on the Internet at: www.philips.com/dynalite

Please ensure that you have completed the following prior to calling our technical support department.

 Check all symptoms in the Troubleshooting list

 Check for any deviations between the installation and the installation instructions

 Make a list of the model numbers of all devices used in the system

SYMPTOM

PROBABLE CAUSE

ACTION

Dimmer does not operate at all. No Service LED

activity. Power supply indicator LED on PCB not lit.

Incorrect connection of mains supply, or no

power available.

Check power supply to dimmer. Check Line and

Neutral input connections.

Power supply indicator LED lit, but no Service LED

activity.

Supply voltage too low, short circuit on

network. Control PCB faulty.

Check supply voltage is at least 75% of rated

voltage. Check 12V terminal voltages.

Disconnect network bus and restore power.

Replace control PCB.

Dimmer will not respond to control panel push

buttons.

Control panel incorrectly wired or incorrect

configuration.

Check operation of LEDs on control panel. Push

button on panel and study response of service

LED.

Dimmer operates properly but circuit breakers keep

tripping.

Instant tripping: - short circuit on load.

Delayed tripping: - dimmer overloaded.

Check load wiring for short circuits. Verify

dimmer loading with current tester (don‟t forget to

de-rate for low power-factor loads and

transformer losses). Check that the breaker

terminals are tight.

Fluorescent lights won‟t dim.

Wrong type of ballast or ballast incorrectly

wired.

Check ballast type. Check actual wiring against

ballast manufacturer‟s diagram. Check 1-

10V/DSI, DALI Broadcast settings.

specification

Supply:

230V ±14% 50/60Hz Single Phase at 40A

Outputs:

4 x 10A dimmed (leading edge phase control) outputs

4 x 10A switched outputs

4 x HF ballast control outputs selectable to DALI Broadcast, 1-10V DC, DSI

Protection:

4 x 10A 6kA single pole thermal magnetic circuit breakers

Regulating Device:

Triac 600V, 40A nom. 400A surge

Switching Device:

Relay 16A nom. (resistive), Fluorescent 800A surge, Incandescent 165A surge,

Power Conditioning;

Regulated outputs

Over voltage protection

Surge protection

Brownout/Sag protection

Spike protection

Soft Start

Interference Suppression:

Iron powder toroidal choke

Rise Time:

100S at 230V

Control Inputs:

1 x RS485 DyNet/DMX512 serial port

1 x programmable dry contact AUX input

User Controls:

Service Switch

Diagnostic LED

Internal Controls:

Programmable Logic Controller

Dynalite Accessory Module enabled

DyNet DC Supply +VE:

200mA (supply for approx 10 panels)

Preset Scenes:

170

Supply Terminals:

Line, Neutral – 2 x 10mm

max conductor size

Output Terminals:

Line, Neutral for each channels 1-8

2 x 4mm

max conductor size

Earth link bar provided

0V/DSI/DALI, +V/DSI/DALI for channels 9-12

1 x 2.5mm

max conductor size

Cable Entries:

Mains – 8 x 25mm dia. knockout

Data – 1 x 25mm dia. knockout

Diagnostic Functions:

(DTK600, DLight or BAS interface required

for displaying and analysing diagnostic data)

Device Online/Offline status

Circuit breaker trip reporting (optional)

Circuit run time tracking

Compliance:

CE, C-Tick,

Ambient Temperature:

0 - 40C ambient temperature, 0% to 95% RH non condensing.

Construction:

Alloy/Steel wall mount case with epoxy finish

Dimensions:

Height 370mm x Width 215mm x Depth 170mm (excludes wall brackets)

Weight:

7.5 Kilograms

DMC810GL Installation Manual Rev E.doc Specifications and design subject to change without notice.

trademarks of Dynalite Intelligent Light Pty Ltd. Not to be reproduced without permission.

Unit 6, 691 Gardeners Road Mascot NSW 2020 Australia Tel: +61 2 8338 9899 Fax: +61 2 8338 9333

E-mail: dynalite.info@philips.com Web: Philips.com/dynalite

1 2 3 4 5 6 7 8

Comments to this Manuals

No comments

Dynalite DMC810GL Installation Manual Page 8

Comments to this Manuals

Related products and manuals for Dimmers Dynalite DMC810GL